- 您现在的位置：买卖IC网 > Sheet目录1243 > SKP16C26A (Renesas Electronics America)DEV EVALUATION KIT M16C/26A
Applications Engineering
Appendix A. Troubleshooting Guide
This section discusses possible problems you may encounter while installing the software (and
drivers) and while running the KD30 Debugger or FoUSB Programmer applications. This section
also discusses the countermeasures and solutions to resolve these problems.
If, for any reason, you cannot resolve the problem, please contact your Renesas representative
for assistance.
A.1 USB Driver Problems
This section discusses the usual problems with the driver installation and how to fix it. The most
common problem encountered is that Windows did not properly install the driver and so the ICD
is not recognized. This may also cause the device status to indicate that the device is not working
properly. An indication of this problem is the ICD status yellow LED - it blinks about 2-3 times a
second. When the driver is installed properly, the yellow LED should only blink every second.
Before trying the following steps, try restarting your PC and see if this resolves the problem. You
can check the status using the Device Manager. If the ICD appears under the Universal Serial
Bus Controllers with NO red X or yellow exclamation point, the driver was installed properly.
NOTE: If you are using Windows 2000 or XP, you need Administrator privileges to install
the drivers.
For cases where the ‘Device Status’ states the device is not working properly, please try the
following:
?
?
?
?
Double-click on ‘Renesas USB-Monitor’ and a Renesas USB-Monitor Properties dialog
box appears.
Click on ‘Driver’ tab and click on ‘Update Driver’ button.
Select ‘Display a list…’ and click on ‘Have Disk’ button.
Specify and locate the ‘C:\MTOOL\FoUSB\USB Drivers’ folder on your PC and install
‘usbmon.sys’ driver.
If you encounter problems on installing the drivers, you can try the following.
(1) Windows 2000
i. Copy the fousb.inf and usbmon.inf files from \USB Drivers folder to
\WINNT\INF folder.
ii. Copy the fousb.sys and usbmon.sys files from \USB Drivers folder to
\WINNT\SYSTEM32\drivers folder.
(2) Windows 98 or XP
i. Copy the fousb.inf and usbmon.inf files from C:\MTOOL\FoUSB\USB Drivers
folder to \WINDOWS\INF folder.
ii. Copy the fousb.sys and usbmon.sys files from C:\MTOOL\FoUSB\USB
Drivers folder to WINDOWS\SYSTEM32\drivers folder.
SKP16C26A User’s Manual Rev. 1.0
14 / 21
June 2004
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SKP32C85-100-CL
DEV EVALUATION KIT M32C/85 100PN
SKP8CMINI-13
BOARD DEV EVALUATION FOR R8C/13
SKP8CMINI-17
KIT EVAL STARTER FOR R8C/17
SKP8CMINI
DEV EVALUATION KIT R8C/11
SL03 10001
CURRENT LIMITER INRUSH 10 OHM 1A
SL03 22101
CURRNT LIMITER INRUSH 220 OHM 1A
SL05 30001
CURRENT LIMITER INRUSH 30 OHM 1A
SL05 4R003
CURRENT LIMITER INRUSH 4 OHM 3A
相关代理商/技术参数
SKP16CMINI28
功能描述:DEV EVALUATION KIT SKP16CMINI28 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
SKP202
制造商:SANKEN 制造商全称:Sanken electric 功能描述:N-Channel MOS FET
SKP202VR
制造商:Sanken Electric Co Ltd 功能描述:MOSFET N-CH 200V 45A TO-263
SKP221M1AE11VMP
制造商:JAMICON 功能描述:
SKP2-30
制造商:Tamura Corporation of America 功能描述:Ind Power Toroid 45uH 1KHz RDL
SKP237/37,5 Z01
制造商:Aavid Thermalloy 功能描述:
SKP2-50
功能描述:固定电感器 2AC 125uH 95mohm RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
SKP2-51
制造商:Tamura Corporation of America 功能描述: